1. Summarize
A recently period, the printing market are having more and more competition, every company are all using the low cost oil based ink to decrease their cost price, that so can acquire the advantage of the market. Because using the oil based ink will have many kind print head clog problem, specially in the color of color magenta, Black and Cyan, the clog problem are more usual, and the plotter haven t got a good auto cleaning process, and after print head get clog, and because not correctly cleaning the print head and get permanence damage usually happened, since the print head get clog and damage happened very often, virtually the cost have increase little by little. In our report there are over 10 thousand of plotter, every plotter have to change 2-3 damaged clogged print head every month, every print head cost RMB3000 each, in one year they have lost more then RMB10,000/year, so that is a really big expense that large print format company lost For the situation above, our company have create the XAAR 128 print head cleaner for maintain the print head, and make the life of print head longer and longer to decrease the high cost every year for large format printer user might have.
3. Configuration
This system are mainly made by power module, FPGA editable logic array,out put driver and out put circuit, LED digital display beeper Print head connector
Before using the impregnate with cleaning fluid is very difficult to make the print head unclog, and there are some who use ultrasonic cleaner cleaning the print head cause permanent damage.
5. Function Parameter Guideline
1, Input electricity---------- AC220V/50Hz
2, Voltage ---------- DC5V
3, Power ---------- 15W
4, Cleaning Frequency ---------- 8KHz
5, Biggest setting hour---------- 15minute
6, Maintain 4 pc of print head at the same time.
Application
This product are make for piezo 128 print head cleaning processing, usually it can be clean in a few minute and back to work again like usual before it was. To make period of cleaning process to print head is very important, because this can make the life of print head much longer, and decrease the waste clog time, and to accord the low cost.
Every kind of large or small format plotter that use Xaar 128 print head all can use the Xaar print head cleaner. Now it is adapt for Xaar Jet MIT INKJETetc.
7. Manual
1Firstly, connect the print head and the Cleaner Machine by the connector before turn on the power.(Notice: the print head and Cleaner Machine must be connected in the correctly by the connector)
2Use 50ml injector to inhale about 50ml cleaning fluid and use the Oil tube to connect the input of the print head and put into the container;
3The cleaning fluid should be 10-20cm deep in container(the front part of print head must be inside of the cleaning fluid)
4Turn on the power of the cleaner (Now you can hear a little noise). Then Push the injector slowly and carefully
5In this time you have to check the cleaning fluid, you have to change the cleaning fluid if you found something dirty, and then clean the print head again and again to finish the Cleaning.
6Turn off power, and disconnect the print head.
Application
This product are make for piezo 128 print head cleaning processing, usually it can be clean in a few minute and back to work again like usual before it was. To make period of cleaning process to print head is very important, because this can make the life of print head much longer, and decrease the waste clog time, and to accord the low cost.
Every kind of large or small format plotter that use Xaar 128 print head all can use the Xaar print head cleaner. Now it is adapt for Xaar Jet MIT INKJET etc.
7. Manual
1,Firstly, connect the print head and the Cleaner Machine by the connector before turn on the power.(Notice: the print head and Cleaner Machine must be connected in the correctly by the connector)
2,Use 50ml injector to inhale about 50ml cleaning fluid and use the Oil tube to connect the input of the print head and put into the container;
3,The cleaning fluid should be 10-20cm deep in container(the front part of print head must be inside of the cleaning fluid)
4,Turn on the power of the cleaner (Now you can hear a little noise). Then Push the injector slowly and carefully
5,In this time you have to check the cleaning fluid, you have to change the cleaning fluid if you found something dirty, and then clean the print head again and again to finish the Cleaning.
6,Turn off power, and disconnect the print head.
Please kindly find the following photos for Xaar 128 Printhead Cleaner
